Skip to content
Lifestyle & Learning

ANSI/ISEA Z87.1 Standard: Complete Safety Eyewear Compliance Guide

In this article

The ANSI/ISEA Z87.1 standard sets the essential technical performance requirements, testing protocols, and permanent marking criteria for eye and face protection devices in industrial, educational, and commercial workplaces across the United States. Published by the International Safety Equipment Association (ISEA) and accredited by the American National Standards Institute (ANSI), Z87.1 ensures protective eyewear resists specific hazards, including impact, non-ionizing radiation, chemical splashes, dust, and fine particles.

Occupational safety standards require employers to assess workplace hazards and equip employees with appropriate personal protective equipment (PPE). The Occupational Safety and Health Administration (OSHA) enforces eye and face protection under safety regulation 29 CFR 1910.133, explicitly referencing ANSI/ISEA Z87.1 as the legal benchmark for compliance. Selecting protective devices that conform to Z87.1 criteria is critical for preventing sight-threatening workplace injuries.

What Is the ANSI/ISEA Z87.1 Standard?

The ANSI/ISEA Z87.1 standard, officially titled American National Standard for Occupational and Educational Personal Eye and Face Protection Devices, defines the design, performance specifications, and safety markings for protective eyewear. The standard applies to safety spectacles (glasses), goggles, face shields, welding helmets, and respirators with integrated eye protection.

  • ANSI/ISEA Z87.1 Framework
    • Impact Ratings & Physical Tests
      • Basic Impact
      • High Impact (+)
      • Mass & Velocity
    • Non-Impact / Lens Specialized Codes
      • Chemical (D3)
      • Dust (D4/D5)
      • Radiation (W/U)

Originally introduced in 1968 as ANSI Z87.1, the standard was created to replace fragmented state and military optical guidelines with a unified nationwide standard. Over time, ownership of the secretariat shifted to the International Safety Equipment Association (ISEA), leading to the modern ANSI/ISEA Z87.1 designation.

Unlike general consumer sunglasses or fashion spectacles, Z87.1-compliant eyewear undergoes rigorous physical and optical testing to confirm its ability to withstand mechanical stress, maintain optical clarity, and prevent structural disintegration when struck by high-speed fragments or hazardous chemical liquids.

OSHA Incorporation by Reference

OSHA enforces eye protection under 29 CFR 1910.133 (General Industry), 29 CFR 1926.102 (Construction), and 29 CFR 1915.153 (Maritime). Rather than drafting distinct testing standards, OSHA incorporates ANSI Z87.1 standards by reference. Under federal guidelines, employers must ensure that protective eye and face devices comply with any of the following revision versions:

  • ANSI/ISEA Z87.1-2020 (Current edition)
  • ANSI/ISEA Z87.1-2015
  • ANSI/ISEA Z87.1-2010
  • ANSI Z87.1-2003

Using non-compliant eyewear in regulated environments constitutes a direct violation of OSHA safety rules and exposes workers to preventable optical trauma.

Core Hazard Categories Covered by Z87.1

The ANSI/ISEA Z87.1 standard structures testing and marking around specific workplace hazards rather than general optical descriptions. Eyewear is tested and rated for one or more distinct hazard classifications:

  1. Impact Hazards: Flying chips, fragments, particles
  2. Chemical Splashes: Liquid droplets, chemical sprays (D3)
  3. Dust Hazards: Coarse dust (D4) and Fine dust/gases (D5)
  4. Optical Radiation: Welding arcs (W), UV (U), Infrared (R), Visible Light / Glare filters (L)

1. Impact Hazards

Flying debris, metal fragments, high-speed chips, projectiles, and snapped cables represent severe physical dangers in manufacturing, construction, and machining. Z87.1 divides impact performance into Basic Impact and High Impact ratings.

2. Optical Radiation

Activities involving welding, brazing, laser operations, thermal cutting, and intense ultraviolet (UV) or infrared (IR) light sources can cause photokeratitis ("welder's flash"), cataracts, and retinal burns. Z87.1 dictates specific transmittance thresholds for protective filters across the light spectrum.

3. Chemical Drops and Liquid Splashes

Working with liquid chemicals, caustics, acids, or biological agents requires protection against liquid droplets and fine sprays. Devices engineered for splash protection prevent fluid ingress around the frame boundary.

4. Dust and Fine Dust Particles

Woodworking, mining, bulk powder handling, and masonry generate airborne dust particles that cause corneal abrasion, irritation, and foreign body injury. Z87.1 defines specific frame seals and ventilation criteria for dust-resistant eyewear.

Testing Requirements: High Impact vs. Basic Impact

The standard distinguishes between basic protective eyewear and high-impact rated eyewear. To earn a high-impact rating, both the lenses and the frame or housing assembly must pass mechanical impact tests without fracturing, dislodging the lens, or touching the eye area of the test mannequin headform.

  • High-Mass Impact Test:
    • 500g Weight
    • 50 inches / 127 cm drop
    • Safety Glasses
  • High-Velocity Impact Test:
    • 1/4" Steel Ball
    • 102–300 mph / 150–300 fps
    • Safety Glasses

High-Mass Impact Test

In the high-mass test, a heavy, pointed steel projectile weighing 500 grams (17.6 ounces) is dropped from a height of 50 inches (127 cm) through a guide tube directly onto the eyewear mounted on an Alderson human-headform. To pass:

  • No part of the lens or frame may crack, fracture, or break through.
  • The lens must remain fully retained within the frame.
  • No component may make contact with the surface of the eye area on the headform.

High-Velocity Impact Test

The high-velocity test evaluates the eyewear’s structural resistance against fast-moving, lightweight projectiles such as metal fragments or flying debris. A 1/4-inch (6.35 mm) steel ball is fired at high speed using a pneumatic gun at multiple angles of impact across the front and sides of the protective assembly.

Speed thresholds vary depending on the product type:

Product Type Projectile Speed (Feet Per Second) Projectile Speed (Miles Per Hour)
Safety Spectacles (Glasses) 150 ft/s ~102 mph
Goggles 250 ft/s ~170 mph
Face Shields 300 ft/s ~205 mph

If any piece detaches, the lens cracks through, or the frame flexes enough to touch the eye region of the headform, the product fails the high-impact threshold and cannot carry high-impact markings.

Basic Impact (Drop Ball Test)

Basic impact safety lenses undergo a standard drop-ball test in which a 1-inch (25.4 mm) steel ball is dropped onto the lens from a height of 50 inches. While basic impact glasses offer minimal protection against minor airborne dust or light drops, high-impact rated protection is required for industrial settings with active flying debris hazards.

Understanding ANSI/ISEA Z87.1 Markings

To verify compliance, ANSI/ISEA Z87.1 mandates that all certified eye and face protection components bear permanent, legible manufacturer markings. Markings must appear on both the frame and the lens (or shield component) to confirm that the entire system meets the standard.

  • Lens Marking: [ Manufacturer Logo ] Z87+ W5 U6 D3
    • Manufacturer Logo: Manufacturer ID
    • Z87+: High-Impact Rated
    • W5: Shade 5 Welding Filter
    • U6: UV Filter Level
    • D3: Chemical Splash Rated
  • Frame Marking: [ Manufacturer Logo ] Z87-2+ D3 D4
    • Manufacturer Logo: Manufacturer ID
    • Z87-2+: High-Impact Rx Frame
    • D3 D4: Splash & Dust Rated

Standard Marking Symbols and Codes

Marking Symbol Meaning / Category Application Details
Z87 Basic Impact Rating Frame or lens meets standard physical requirements without high-velocity testing.
Z87+ High-Impact Rating Lens and frame passed high-velocity and high-mass impact testing.
Z87-2 Prescription Eyewear (Rx) Indicates frame is designed and certified for prescription safety lenses.
Z87-2+ High-Impact Prescription Prescription-ready frame meeting high-impact structural testing.
W [Shade #] Welding Filter Protection Indicates shade rating for arc welding/cutting (e.g., W1.3 to W14).
U [Scale #] Ultraviolet (UV) Filter Denotes UV attenuation level, ranging from U2 (minimal) to U6 (maximum).
R [Scale #] Infrared (IR) Filter Indicates protection level against thermal IR radiation (scale R1.2 to R10).
L [Scale #] Visible Light Filter Specifies solar glare or general light reduction scale (scale L1.3 to L10).
D3 Droplet and Splash Protection Sealed design that prevents liquid entry during splash testing.
D4 Dust Protection Goggles or masks that restrict entrance of coarse airborne dust.
D5 Fine Dust Protection Tight-sealing barriers tested against micro-fine dust particles.
S Special Purpose Lens Tinted or custom lenses designed for specific technical applications.
V Variable Tint Lens Photochromic lenses that adjust light transmission dynamically.
H Headform Size Indicator Designed for smaller head sizes (compact / small face fits).

Where to Find Markings

  • Lenses: Markings are etched or stamped into the corner or perimeter of the lens, clear of the central line of sight.
  • Frames: Markings appear on the inner side of the temple arm, inside the brow bar, or on the rim edge.
  • Face Shields & Visors: Markings are stamped along the top mounting edge or lower corner of the visor.

Evolution of the Standard: 2010, 2015, and 2020 Revisions

The ANSI/ISEA Z87.1 standard undergoes regular revisions to keep pace with manufacturing advancements, optical technologies, and emerging industrial hazards. Understanding these historical updates clarifies why certain markings exist.

  • 2010 Revision: Transitioned from product-based to hazard-based selection (Explicit markings for splash D3, dust D4/D5, radiation)
  • 2015 Revision: Updated coverage requirements for small headforms (H) and refined prescription (Rx) test parameters
  • 2020 Revision: Added criteria for anti-fog technology, extended facial coverage, and relaxed optical distortion rules for small headforms

The 2010 Milestone: Shift to Hazard-Based Testing

Prior to 2010, the Z87.1 standard classified eyewear primarily by device design (e.g., spectacles vs. goggles). The 2010 revision introduced a hazard-based model. Instead of treating all safety glasses identically, eyewear earned specialized markings based on distinct hazards (e.g., splash D3, dust D4, ultraviolet radiation U).

The 2015 Revision

The 2015 update refined testing for smaller head sizes, establishing standardized criteria for "small headform" testing marked with an H. It also clarified rules surrounding prescription safety lenses, requiring prescription lens laboratories to re-mark frames when fitting custom lenses into Z87-2 frames.

The 2020 Revision: Modern Refinements

The ANSI/ISEA Z87.1-2020 edition introduced several notable technical updates:

  • Anti-Fog Performance Criteria: Established optional standardized testing criteria for anti-fog optical coatings. Lenses passing the test carry an AF designation.
  • Expanded Field of View & Coverage Requirements: Refined minimum facial coverage geometries for high-impact frames to prevent peripheral particle entry.
  • Relaxation of Optical Criteria for Special-Purpose Lenses: Adjusted permissible optical distortion thresholds for specialized dark tints and extreme wrapped lenses without compromising impact resistance.

How to Select Compliant Safety Eyewear: Step-by-Step

Selecting the correct eye protection requires matching the specific hazards present in the work area to the appropriate ANSI/ISEA Z87.1 marking code. Safety managers and procurement teams can follow this process:

  1. Step 1: Conduct Workplace Hazard Assessment
    • Identify flying objects, chemical liquids, dust, or radiation
  2. Step 2: Determine Required Impact Level
    • Select Basic (Z87) or High Impact (Z87+)
  3. Step 3: Match Specialized Hazard Codes
    • Verify D3 (Splash), D4/D5 (Dust), or W/U/R (Radiation) markings
  4. Step 4: Verify Frame & Lens Compatibility
    • Ensure both components carry matching ratings (e.g., Z87-2+)

Step 1: Conduct a Formal Job Hazard Analysis (JHA)

Assess the workplace for environmental risk factors:

  • Mechanical: Grinding, cutting, drilling, chipping, or metalworking (flying particles).
  • Chemical: Pouring acids, mixing solvents, dealing with pressurized liquid lines.
  • Radiant Energy: Gas welding, arc welding, plasma cutting, torch soldering, or high solar UV exposure.
  • Atmospheric: Woodworking dust, cement powder, sandblasting, chemical fumes.

Step 2: Determine the Required Impact Threshold

If the hazard assessment identifies potential high-velocity debris, chips, or fragment risks, basic safety glasses are insufficient. High-Impact (Z87+) eyewear must be specified. Frame and lens markings must both show the "+" symbol (e.g., Z87+ or Z87-2+).

Step 3: Match Eyewear Style and Secondary Markings to Specific Hazards

  • Flying Debris Only: High-impact safety spectacles with side shields (Z87+).
  • Chemical Splashes: Unvented or indirect-vented safety goggles marked D3. Standard safety glasses with side shields do not provide splash protection.
  • Coarse or Fine Dust: Indirectly vented or sealed foam goggles marked D4 or D5.
  • Welding and Torch Work: Helmets or goggles equipped with filter lenses marked with the appropriate shade scale (W1.3 to W14).

Step 4: Validate Physical Fit and Optical Compatibility

Improperly fitted eyewear creates gaps through which foreign bodies enter. Ensure that safety frames fit tightly along the facial contour without creating painful pressure points. If prescription lenses are required, verify that the complete assembly (frame and custom optics) carries the Z87-2 marking and is processed by an accredited optical laboratory.

Common Compliance Mistakes and Misconceptions

Despite widespread familiarity with safety glasses, compliance errors often occur in practical workplace environments:

Mistake 1: Relying on Streetwear Glasses with Add-On Side Shields

Attaching removable plastic side shields to standard non-certified prescription glasses does not create Z87-compliant safety eyewear. Everyday fashion frames lack the structural rim retention, shatterproof materials, and high-mass impact resistance mandated by Z87.1 testing.

Mistake 2: Assuming All Safety Spectacles Protect Against Chemical Splashes

Standard safety glasses leave gaps along the brow, cheeks, and sides. When handling liquid caustics or solvents, liquid droplets can bypass safety glasses. Only indirectly vented goggles marked D3 satisfy chemical splash safety rules.

  • No Splash Protection:
    • Device: Safety Glasses (Z87+)
    • Features: Gap / Gap
    • Detail: Liquid can enter from top, side, or bottom.
  • Certified Splash Protection:
    • Device: Sealed Goggles (Z87+ D3)
    • Features: Full Perimeter Seal
    • Detail: Body forms continuous barrier against fluids.

Mistake 3: Mixing Non-Impact Lenses with High-Impact Frames

A frame stamped Z87+ only provides high-impact protection when paired with high-impact lenses marked +. Placing non-impact lenses into a high-impact frame reduces the overall assembly rating to basic impact performance.

Mistake 4: Using Damaged or Scratched Lenses

Pitted, cracked, or deeply scratched lenses suffer from compromised structural integrity and increased light scattering. Severe scratching reduces high-impact resistance, rendering the eyewear prone to shattering upon physical impact. Damaged safety devices must be replaced immediately.

Technical Comparison: Non-Impact vs. High-Impact Eyewear

To select the right gear for your workforce, review this side-by-side comparison of testing metrics, marking criteria, and primary workplace applications:

Feature / Criteria Basic / Non-Impact Eyewear High-Impact Eyewear
Primary Lens Marking Z87 Z87+
Prescription Marking Z87-2 Z87-2+
Drop-Ball Impact Test 1-inch steel ball from 50 inches Passed (Baseline)
High-Mass Impact Test Not Required Passed (500g pointed projectile from 50 inches)
High-Velocity Impact Test Not Required Passed (1/4" steel ball at 150-300 fps)
Frame Structural Requirement Basic retainment High energy absorption & zero eye-headform contact
Common Form Factors Light dust glasses, tinted reading safety wear Industrial safety glasses, high-velocity goggles, face shields
Typical Use Cases General inspection, lab work without splash, light assembly Machining, grinding, masonry, construction, metal cutting

ANSI/ISEA Z87.1 Professional Advice Limitations

Occupational Safety Limitation: Eye protection rules vary depending on industrial applications, state-plan OSHA rules, and site-specific hazard evaluations. Environmental factors such as chemical toxicity, radiological hazard intensity, and explosive risk may mandate secondary protection (such as wearing a full-face shield over safety goggles) or compliance with additional standards (such as ASTM or NFPA guidelines). Always consult a certified Industrial Hygienist (CIH) or Certified Safety Professional (CSP) to perform a formal workplace hazard assessment before finalizing PPE choices.

Frequently Asked Questions

What is the difference between Z87 and Z87+?

Z87 indicates basic impact testing compliance. Z87+ indicates that the protective eyewear passed rigorous high-impact testing, including high-mass and high-velocity projectile impact tests. For environments involving flying metal, wood chips, high-speed machinery, or heavy impacts, Z87+ rated protection is required.

Is ANSI Z87.1 compliance legally mandatory under OSHA?

Yes. OSHA standards 29 CFR 1910.133 (General Industry) and 29 CFR 1926.102 (Construction) mandate that employers provide workers with eye protection that conforms to ANSI Z87.1 standards. Using non-compliant eyewear in designated hazard zones can result in OSHA citations and fines.

Can regular prescription glasses be made ANSI Z87.1 compliant with side shields?

No. Standard everyday prescription frames do not satisfy ANSI Z87.1 structural integrity or lens retention tests. Adding clip-on side shields to street glasses does not satisfy OSHA requirements. Certified prescription safety eyewear must feature frames stamped Z87-2 or Z87-2+ and be fitted with certified safety lenses.

How do I know if my safety glasses are high-impact rated?

Look for the plus sign (+) etched onto the lens and stamped into the frame. High-impact lenses display markings such as Z87+ or a combination code like Z87+ U6. If only Z87 appears without a +, the eyewear is rated for basic impact only.

What does the D3 marking on safety goggles mean?

The D3 designation indicates that the protective device has passed liquid splash testing. Goggles marked D3 feature indirect ventilation or continuous rubber/silicone seals designed to prevent chemical droplets, acids, and liquid splashes from reaching the eyes.

How often should ANSI Z87.1 safety glasses be replaced?

Safety eyewear should be replaced immediately if the lenses or frames show cracks, pitting, structural distortion, or severe surface scratching. Scratches compromise the lens's shatter resistance under impact. Eyewear that has sustained a major high-speed impact should be taken out of service and replaced, even if no visual damage is obvious.

Practical Action Plan for Compliance

To maintain safety compliance and safeguard worker vision:

  1. Audit Existing Eyewear inventory: Inspect all safety glasses, goggles, and face shields currently in use. Verify that permanent manufacturer markings (Z87, Z87+, D3, W, etc.) are clearly visible.
  2. Review Workplace Hazard Assessments: Ensure that jobs involving grinding, cutting, chemical handling, or welding specify the correct impact level and hazard codes rather than generic "eye protection."
  3. Establish a Prescription Safety Glasses Program: Ensure employees requiring vision correction receive certified Z87-2 frames and lenses through a qualified safety optical vendor, rather than relying on everyday streetwear glasses.
  4. Enforce Storage and Maintenance Protocols: Implement protective cases and micro-fiber cleaning stations across work floors to extend lens life and prevent scratch-induced structural degradation.